Anyone have specs at .050 for Engle Cam K58 intake/k60 exhaust with 110 lsa?

[1Bad70Charger]

Taking a serious look at a custom Engle cam-K58 intake/k60 exhaust on a 110* LSA.  The cam is not currently listed on Engle's website as they were recently bought out, but if anyone has the specs at 0.050 duration that would be greatly appreciated. 

[Ghoste]

I believe that specs out at 245 intake and 253 exhaust. 

[1Bad70Charger]

I believe that specs out at 245 intake and 253 exhaust. 

Thank you Ghost! 

And do you know what the lift would be kind sir duration at 0.050?

[Ghoste]

.560 and .575?  I'm going by old notes I have scribbled around here, Ron will know for sure.  I think he has the entire cam catalog for Engle, Crower, Comp, and Lunati committed to memory.

[1Bad70Charger]

.560 and .575?  Ron will know for sure, I think he has the entire cam catalog for Engle, Crower, Comp, and Lunati committed to memory.

Thanks Ghoste, I appreciate it!


Ron, I don't want to burden you with another pm     so if you see this I would really appreciate it if you could post up the specs on this cam at duration of 0.050.  

[firefighter3931]

.560 and .575?  Ron will know for sure, I think he has the entire cam catalog for Engle, Crower, Comp, and Lunati committed to memory.

Thanks Ghoste, I appreciate it!


Ron, I don't want to burden you with another pm     so if you see this I would really appreciate it if you could post up the specs on this cam at duration of 0.050.  

Jim,

K58 is 230*@.050 & .520 lift
K60 is 238*@.050 & .534 lift

Both of these lobes will work with an OEM non adjustable rocker arm 


Ron

[1Bad70Charger]

.560 and .575?  Ron will know for sure, I think he has the entire cam catalog for Engle, Crower, Comp, and Lunati committed to memory.

Thanks Ghoste, I appreciate it!


Ron, I don't want to burden you with another pm     so if you see this I would really appreciate it if you could post up the specs on this cam at duration of 0.050.  

Jim,

K58 is 230*@.050 & .520 lift
K60 is 238*@.050 & .534 lift

Both of these lobes will work with an OEM non adjustable rocker arm  


Ron

Thanks Ron, I appreciate it.  


That is smaller than I thought it would be, I was really like the specs. that Ghoste was quoting!  

[Ghoste]

Before you run away from this thread Ron, the notes I have were info I have attributed to you.  Did I miscredit you or did the specs ever change or any other reason (realistic reasons outside of the obvious "cuz Ghoste is an idiot" ones  ) that I had written down such different specs?

[firefighter3931]

Before you run away from this thread Ron, the notes I have were info I have attributed to you.  Did I miscredit you or did the specs ever change or any other reason (realistic reasons outside of the obvious "cuz Ghoste is an idiot" ones  ) that I had written down such different specs?

Nope....Ghoste ain't no idiot  If you multiply the lobe lift by 1.6 the results are close to what you stated. Possibly i quoted gross lift based on a 1.6:1 rocker ratio ? I can't remember the specific thread as there have been so many. 

Seasons Greetings Shawn 



Ron

[Ghoste]

They're older notes and I'm guessing it's from a pm as opposed to a thread because I've asked you a pile of cam questions outside of the forum.  Since we're here then, what do you have for the K56 and 54?
And all the holiday best to you too buddy!  

[firefighter3931]

Shawn, the specs for the other lobes are :

K56 is 224@.050 & .504 lift (1.5 RR)
K54 is 214@.050 & .470 lift (1.5 RR)

It would be nice if the "new" owners of Engle Racing Cams would publish the old catalog....apparently those lobe profiles are still available even though there is no reference on the website. 


Ron

[Ghoste]

Hmm, well I have those two correct.