News:

It appears that the upgrade forces a login and many, many of you have forgotten your passwords and didn't set up any reminders. Contact me directly through helpmelogin@dodgecharger.com and I'll help sort it out.

Main Menu

71 Super Bee fender emblems question

Started by 71butterbee, November 15, 2007, 10:23:20 AM

Previous topic - Next topic

71butterbee

Is the correct mount of the fender emblems stick-on or pin? If they are pin on does any one know the correct dimension for locating the emblem?
Thanks

68RT4ME

 Try going to www.71superbee.com  Member here by the name "JohnnyBEE" runs it and has a ton of info there that may help you out.  :icon_smile_big:
'69 Charger R/T, T5, Tan Top, Tan Interior, Black Stripe. Complete numbers matching 440 4Spd

Skyview69

Pins are correct.  In this pic below you can see where the holes are for the emblem (look above the rust hole).  I could measure if you need me to.

71butterbee

Quote from: Skyview69 on November 15, 2007, 02:03:15 PM
Pins are correct.  In this pic below you can see where the holes are for the emblem (look above the rust hole).  I could measure if you need me to.

If you could do that I would really appreciate it. Thanks! Email the dimension to KTMguyforever@yahoo.com.
Thanks again!

Skyview69




WM23N1

The super bee emblems are stick on for 71 fenders. They are hard to find but just buy some 70 that have the pins and whack them off and use trim adhesive to mount them.
1971 Super Bee 383 "The WM23N1" http://1971-1974dodgecharger.com/

General_01

71's are stick on. You might try Year One. They might have them.
1971 Dodge Charger Super Bee
496 stroker
4-speed

Skyview69

Quote from: WM23N1 on November 15, 2007, 10:42:46 PM
The super bee emblems are stick on for 71 fenders. They are hard to find but just buy some 70 that have the pins and whack them off and use trim adhesive to mount them.

The fender in the picture is a 71 fender that has the pin type emblem.  I still have the emblem.

WM23N1

Quote from: Skyview69 on November 16, 2007, 07:20:47 AM
Quote from: WM23N1 on November 15, 2007, 10:42:46 PM
The super bee emblems are stick on for 71 fenders. They are hard to find but just buy some 70 that have the pins and whack them off and use trim adhesive to mount them.

The fender in the picture is a 71 fender that has the pin type emblem.  I still have the emblem.
It possible both were used but I have only seen stick on type.
1971 Super Bee 383 "The WM23N1" http://1971-1974dodgecharger.com/

41husk

I purchased the pin style, the 70 did not have the script with the bee on the fender.
1969 Dodge Charger 500 440/727
1970 Challenger convertible 340/727
1970 Plymouth Duster FM3
1974 Dodge Dart /6/904
1983 Plymouth Scamp GT 2.2 Auto
1950 Dodge Pilot house pick up

Skyview69

Quote from: 71butterbee on November 15, 2007, 02:49:16 PM
Quote from: Skyview69 on November 15, 2007, 02:03:15 PM
Pins are correct.  In this pic below you can see where the holes are for the emblem (look above the rust hole).  I could measure if you need me to.

If you could do that I would really appreciate it. Thanks! Email the dimension to KTMguyforever@yahoo.com.
Thanks again!

From the inside of the fender to the center of the bottom hole is 5"
From the crease in the fender up to the center of the bottom hole is 2 1/2"

WM23N1

Quote from: 41husk on November 16, 2007, 01:31:40 PM
I purchased the pin style, the 70 did not have the script with the bee on the fender.
I think the pin emblem was used on the hood of the 70
1971 Super Bee 383 "The WM23N1" http://1971-1974dodgecharger.com/

71butterbee