BEA Restoration Parts

[hollywood1336]

Anyone have anything good or bad to say about BEA Restoration parts. I have not seen them before.
Thanks,

[79JON]

I recently bought a dash pad from them for my 1970 Charger.   Great great piece!   I have not installed it yet but it is very nice.  My brother has installed the dash pads on a few other cars he has restored and he says they fit great and is the best pads around.  Hope that helps.

[billssuperbird]

I got my dash pad from them looks and fits great. 

[hollywood1336]

Thanks Guys, getting ready to order some upper door pads, just wated to make sure they were worth while.

[Dino]

I hear the pads are pretty good but the grain doesn't match the originals.  If you are ordering all 4 then it'll look great, only 2 and it "may" look a bit off.

[Troy]

Haven't seen them before? If you think of AMD as sheet metal and Legendary as interior then BE&A is "everything else". BE&A and PG Classics are essentially the same (if you've heard of that company). The difference, typically, is that BE&A sells parts with the correct part numbers/markings and has to pay Mopar licensing fees - which means the price is usually higher for the exact same part. In many cases, BE&A/PG is the only manufacturer (68 Charger tail light assemblies for example). In cases where there are multiple manufacturers of the same part the BE&A version is typically more correct and/or nicer.

Troy

[NHCharger]

Been dealing with Mike from BE&A for a few years now. Good guy, no problems.

[41husk]

I have ordered from them in the past and will again in the future.  great customer service!

[BananaDan]

Been dealing with Mike from BE&A for a few years now. Good guy, no problems.

+1 

[Ghoste]

I've had good luck with their stuff too. 

[Chatt69chgr]

I've ordered a lot of parts from both Mike at BEA and Peter at PG-Classics.  As has been said, Mike just imports the stuff that Peter has made in China and then sells them in the USA with the Mopar Part #'s (if they had a part number visible).  Peter's part has the Mopar p/n ground off.  

Most everything that I've ordered has been very good to excellent.  Just wish that Peter would repop a few parts that so far he has not made.  FOR EXAMPLE---69 Charger Lower Dash Pads (AC car) and the heater control bezel.  The bezel that he has shown in his catalog is not the right part---I know because I ordered one and had to send it back on my dime.  

He has been promising to have the Lower Dash pads for at least 3 years that I know of.  Of course, there is Just Dashes in CA that would end up costing twice as much.

[8WHEELER]

I've ordered a lot of parts from both Mike at BEA and Peter at PG-Classics.  As has been said, Mike just imports the stuff that Peter has made in China and then sells them in the USA with the Mopar Part #'s (if they had a part number visible).  Peter's part has the Mopar p/n ground off.  

Most everything that I've ordered has been very good to excellent.  Just wish that Peter would repop a few parts that so far he has not made.  FOR EXAMPLE---69 Charger Lower Dash Pads (AC car) and the heater control bezel.  The bezel that he has shown in his catalog is not the right part---I know because I ordered one and had to send it back on my dime.  

He has been promising to have the Lower Dash pads for at least 3 years that I know of.  Of course, there is Just Dashes in CA that would end up costing twice as much.

I bought a set of tail lights from BE&A at least four years ago, had to send the first two sets back, the paint was not good. I think it was early in the run.

I have bought many other items from Mike over the years with no problems, and fast shipping, I would recommend him.

After saying that, I called PG, and decided to take advantage of there lower price, and 15% off, and bought another set of tail lights, and
a couple sets of side markers.

To my suprise, both of the tail light housings had all the part numbers, evan though I did ask him if they had the numbers,
and he said no ''and I had already known that''. We grind them all off he tells me. Well not on this set, but the Petastar was not there, but I was happy
for the price, and great quality this time.

Dan

[Cooter]

Bought the roof chrome (pot metal) for son's 66 Plymouth. Awesome repro.

[hemi68charger]

Everything I have gotten from Mike at BE&A has been top-notch. If there was a flaw, he took care of it. I had one item over the years that was bad and he replaced it no-prob.

[Lord Warlock]

I've ordered a few parts from them, and was happy with what i bought, sometimes it took a little longer to get than other stuff i'd ordered on the internet, but wasn't delayed enough to complain. 

[polywideblock]

i'v got a few parts from PG their customer service is A1       had a problem with a part and had a replacement within a week

[shart70rt]

Have never had a problem with BEA, with several orders. Knowledgable, friendly, and great quality.

[Charger-Bodie]

I've ordered a few parts from them, and was happy with what i bought, sometimes it took a little longer to get than other stuff i'd ordered on the internet, but wasn't delayed enough to complain. 

Slow shipping from B/E&A ? They have always been the fastest shippers I deal with.

[bill440rt]

No problems, here either. If there ever was, Mike (BE/A) was always helpful to resolve it. 
Never had to mail order anything, as I used to see their huge swap meet spot at the larger Mopar shows. From what I understand they no longer do swap meets, so I guess it's now mail order only.

[Aero426]

Mike Ross / BEA is an upstanding guy and seller.

[Daytona R/T SE]

Mike Ross / BEA is an upstanding guy and seller.

[68blue]

No issues, my 68 is wearing plenty of stuff from them.