Uhm. Shouldn't this be level?

[Dino]

I placed the Pro Flo 4 intake on the engine and the air cleaner on top and noticed the engine is not level. I removed the air cleaner and laid a straight edge on the throttle body and it's off quite a bit. What the heck?

[Mopar Nut]

How's your engine mounts?

[Dino]

They should be new. I dropped the engine in 7 years ago. I never got beyond mounting the stock intake and had no idea it was off.

[b5blue]

Loosen all the bolts and see if it will shift? 

[Dino]

Will do!   

[birdsandbees]

Yep, loosen the mount bolts in the K frame and lift to take the load off and twist..

[Dino]

I totally forgot about this until today when I was under the car. I looked towards the back and saw the transmission pan was not parallel to the crossmember, at all. Then I remembered we had a hell of a time getting the bolts to line up with the new rubber mount on the tail shaft. I put a stand under the tail and removed the crossmember. Next up is loosening motor mounts at the k member and see if I can straighten it out with the engine hoist. Now I don't remember where I got the trans mount, but it's obviously not a good one. Which one do you guys use?
 

[Dino]

Another question. I loosened the engine mount to K member bolts.  Hooked the chain to the driver side of the engine, which sits too low, and gave the lift a few pumps. The engine came up a bit, and although I'm not positive it's where it needs to be, it looks a whole lot better. Now when I release the lift the engine drops back to where it was, so how can I make sure the passenger side is at its lowest before I tighten everything down?

[Dino]

Ok so I lifted the driver side, and pulled down the passenger side with a strap. It's way more level than before, but it's not perfect. Should it be?

[Dino]

Ok so it helps when I actually bolt the intake manifold down.   

[b5blue]

The mounts are designed to adjust: https://shop.advanceautoparts.com/p/anchor-engine-mount-front-right-front-left-1-piece-2250/5300223-p?product_channel=local&store=5273&adtype=pla_with_promotion&product_channel=local&store_code=5273&&&gclid=CjwKCAjw1MajBhAcEiwAagW9MTEizTJpVx8Yegq-wQ3xt8xtXxj95tYqmUz7k5TwJx0uqSAnqbBtuxoC_0YQAvD_BwE&gclsrc=aw.ds
See the big hole? You can pry on the base to adjust but harder to do after once tightened. (Clamped force.)

[Dino]

Yeah I was surprised how much it moved. Makes sense now why it was a hassle to get the trans crossmember to fit. 
Once the engine was straight, everything fit into place.

[b5blue]

 

[71 SE3834V]

I totally forgot about this until today when I was under the car. I looked towards the back and saw the transmission pan was not parallel to the crossmember, at all. Then I remembered we had a hell of a time getting the bolts to line up with the new rubber mount on the tail shaft....
 

I remember this. I also remember the car not being very high in the air creating a tight space to crawl under. Probably why we could get a good eyeball on the alignment issue.
I may have a similar issue as my trans tail shaft is not centered in the tunnel like it should be. Already tried loosening the engine mount to k frame bolts (helped but still not right) but didn't think to loosen the k frame bolts, Duh!

[Dino]

I totally forgot about this until today when I was under the car. I looked towards the back and saw the transmission pan was not parallel to the crossmember, at all. Then I remembered we had a hell of a time getting the bolts to line up with the new rubber mount on the tail shaft....
 

I remember this. I also remember the car not being very high in the air creating a tight space to crawl under. Probably why we could get a good eyeball on the alignment issue.
I may have a similar issue as my trans tail shaft is not centered in the tunnel like it should be. Already tried loosening the engine mount to k frame bolts (helped but still not right) but didn't think to loosen the k frame bolts, Duh!

That's right, we didn't have ideal circumstances. If you need help with yours let me know. I'm off for a week starting Saturday.

[71 SE3834V]

Fix mine, Ha! That's a good one there. I haven't even gotten the car out this year although I did have to move it out to get to one of my boats I sold. But the car went right back in the backyard. Life's been kicking my butt lately with other issues to deal with mainly repairs on my Ram. A lot of changes around here since we last wrenched together.
Where are you at nowadays? Talk to you sometime....

[Dino]

Fix mine, Ha! That's a good one there. I haven't even gotten the car out this year although I did have to move it out to get to one of my boats I sold. But the car went right back in the backyard. Life's been kicking my butt lately with other issues to deal with mainly repairs on my Ram. A lot of changes around here since we last wrenched together.
Where are you at nowadays? Talk to you sometime....

Sorry to hear you're getting your butt kicked. If you need help with anything, just say the word. I'm in Jackson now, just outside of the city. You're more than welcome to come by. I'm off this week and hope on firing up the engine for the first time since we pulled it out of the car!