swap 2.76 to 3.55

[Mrs.Caveman]

hi guys!it might sound stupid but i think i can confidently ask questions!my car has 2.76 sure grip in now and would like to swap it to 3.55!what do i need to buy and where?know nothing about rear ends so no clue!if i had 2.76 sure grip would it stay sure grip with 3.55 or have to get a 3.55 sure grip!can picture this whole thing!is it hard to swap it?thanks

[clanton]

You are gonna have to change your speedometer gear. Depending on what kinda of car it is, the trans gearing might have been built around the 2.76, you wont be starting out in first, that and crusing at 60, motor will be winding.

[68RED4SPEED]

First you will need this http://cgi.ebay.com/ebaymotors/DODGE-MOPAR-8-75-3-55-89-case-RING-AND-PINION-USA-GEAR-/120684899205?pt=Motors_Car_Truck_Parts_Accessories&hash=item1c19616b85 or similar, and one new nut, one crushsleeve if its a 489 housing, gasket for housing and some tools, this can give you some help http://www.moparmusclemagazine.com/howto/mopp_0308_mopar_rear_end_gears_set_up/preload.html I used it myself when I did mine, check first out what house you have 741 742 or 489, sure-grip is the same for all house, maybe something forgotten.
Sven

[clanton]

I highly doubt its a sure grip with 2.76. thats granny gearing.

[68RED4SPEED]

I bought a e-body 8 3/4 with cone sure-grip and 2.76  .

[Mrs.Caveman]

ok thanks!my car is not here yet still on her way and just wanna get the parts that i wanna change or missing!know clue what housing.its a 727 383.was told got posi end in it!is 3.23 would be better for cruising but enough for fast launching?mostly will cruise with her but also want to be able to burn so rubber!

[John_Kunkel]

The 3.23 is the best all around gear IMHO. If all you want to do is burn rubber you don't need Sure-Grip, a one-legger is easier to spin.

[Piston_Freddy]

I also believe that the 3.23 would be the best gear.And if you want to to a lot of rubber burning, then this mod is a must! http://www.dodgecharger.com/forum/index.php/topic,13216.0.html 
Or get a torque strap.

[Back N Black]

I have a 3.23, its a good cursing gear and still can lay down rubber if the need should arise.

[Charger-Bodie]

ok thanks!my car is not here yet still on her way and just wanna get the parts that i wanna change or missing!know clue what housing.its a 727 383.was told got posi end in it!is 3.23 would be better for cruising but enough for fast launching?mostly will cruise with her but also want to be able to burn so rubber!

What Charger did you end up getting?

[Piston_Freddy]

ok thanks!my car is not here yet still on her way and just wanna get the parts that i wanna change or missing!know clue what housing.its a 727 383.was told got posi end in it!is 3.23 would be better for cruising but enough for fast launching?mostly will cruise with her but also want to be able to burn so rubber!

What Charger did you end up getting?

She bought this one. http://www.dodgecharger.com/forum/index.php/topic,76248.0.html

[Charger-Bodie]

Looks like a great car. I noticed that one when it was for sale.

[Mrs.Caveman]

thanks guys!3.23 it is then!dont wanna do a lot of burnings but cant have a charger and not do it!Veronika

[68RED4SPEED]

You will also need this http://marketplaceadvisor.channeladvisor.com/storefrontprofiles/DeluxeSFItemDetail.aspx?sid=1&sfid=92390&c=0&i=19350344 and this
http://marketplaceadvisor.channeladvisor.com/storefrontprofiles/DeluxeSFItemDetail.aspx?sid=1&sfid=92390&c=0&i=16587820

[mikesbbody]

Yes, your Top end Speed will be better with 2.76's as opposed to 3.23's or 3.55's and your gas Mileage will be better with 2.76's but...Slow take off!  I have 3.55's on my Charger but I have 28 inch tall Tires on the back (I think your's are 26's?) I'm thinking about going with some 3.9's for a even better take off (low to mid range driving is pretty much all I do) I hardly drive on the Highway at all. I drove a Charger with 3.23's and it felt slow compared to mine with 3.55's (The take off) But I agree with the Guy's you can't go wrong with 3.23's 

[Cooter]

I can't believe no one has asked about tire size yet..All the 3.55 gears in the world won't do any good if she's running a 30" tall tire....

[flyinlow]

I assume you have an 8 3/4 inch axle. Why not have more then one carrier. I have a 3.23, 3.55 and a 4.10 carriers. Spares are aways nice if you like doing burnouts.

[mikesbbody]

Cooter, i mentioned tires i took a look at her charger not 28's on the back for sure! Taller tires do make a difference regarding lower gears so im not sure what you mean? No matter i love my 3.55's with my 28's on the back i personally dont like 3.23's but whatever each to his own

[mikesbbody]

I assume you have an 8 3/4 inch axle. Why not have more then one carrier. I have a 3.23, 3.55 and a 4.10 carriers. Spares are aways nice if you like doing burnouts.

I'm kinda in the same situation and agree. I have 3.55's in the Car now, and have a nice 489 with 3.9's ready to go in at some stage.
In the Future, I will have a taller tire than a 28 (29+) due to my 17's if I can get 2 18's for the back, it may be even Taller! I have another Suregrip (741) but I havent got around to putting it back together I won't put 3.23's in there maybe 3.7's 
You gotta understand these rear ends are not cheap (good ones) espicially for overseas Charger Owners.

[gtx6970]

http://www.doctordiff.com/

Talk to Cass. He can build you anything your little heart desires, that your wallet can back up

[Mrs.Caveman]

thanks guys!i was told she has 14x7 wheels with 235/60/14 tires all around!dont know how tall they are!when i get the 3.23 sure grip gear do i have to take off the axel from the car or can do it on it!to be honest i can't picture,as i never seen it before,what it involves the whole gear swaping!have to start to learn somewhere!ordered the service manual from ebay thats gonna keep my stupid questions away!dont wanna do a lot of burnouts but knowing myself...thanks again

[Brass]

I had those tires when I bought my car.  They are 25.1" according to this:
http://vexer.com/68rt/old_outdated_badly_coded_old_old_old_wheelguide.html

[Charger-Bodie]

thanks guys!i was told she has 14x7 wheels with 235/60/14 tires all around!dont know how tall they are!when i get the 3.23 sure grip gear do i have to take off the axel from the car or can do it on it!to be honest i can't picture,as i never seen it before,what it involves the whole gear swaping!have to start to learn somewhere!ordered the service manual from ebay thats gonna keep my stupid questions away!dont wanna do a lot of burnouts but knowing myself...thanks again

On an 8 3/4 rear you can simply pull the axles and then the gear chunk. Very simple really. 3.23 will be about perfect with those 14 inch wheels and those tires,but if you get taller ones 3.55 is better as the taller the tire the more it raiser the final ratio.

[moparguy01]

ya the 8 3/4 pig  swap is one of the best designs. The only one I like better was a ford 9" base in a race car which the axle shafts were splined on each end. Take 3 allen bolts off a cover, thread in a small bolt and slide out the axle by 6" on both sides and go to town.

[Mrs.Caveman]

im planning to get some 15x7 magnum 500s,love them,with 255/60/15 all around!is 3.23 good with it still?what the widest tire i can go with those 15x7 magnums?thanks guys,Veronika