Big block to Small conversion

[cudaken]

GMC Big Bore 6-71 Super Charger polished and never ran Lifetime warranty on blower it self.
Blower gaskets
BDS front cover new with sight hole and pressure relief new
Dyer drive modified to by BDS to fit BB Mopar or BB Chevy (yuck) new
3 speed wiper motor to clear blower
BDS top cover for dual crabs, used I think
Modified rear bearing plate and cover ready to run new
Blower straps, SEMA but out of date, no lower hook ups
Dual Edelbrock's 600 CFM and jetted for a blower, have 10 hours on them and sealed used
BDS Lower drive with dual keyways new
3" dive belt new
10 + or - drive gears 1/2 pitch and new
Holley 2 regulator1 used and 1 new
Aluminum blower scoop, low profile used but looks good
BDS 833 tented polished intake used and is a custom cut intake for better fit
BDS poop off, new
V-belt drive for P/S and ALT
Reed blower cam, has 90 miles on it and look fine. Will list specks if contacted
18 feet of 1/2 stain less steel line new
1 used and one new Holley blue pump
MSD timing control used can adjust timing from under the dash
9 quart pan, 90 miles and pick up.

74 440 30 over and will be ready to bolt together with .004 piston clearances
Block was bored with plates
69 440 crank 10 /10 oil holes chamfered
Balanced lower end
Chrome Timing Chain Cover
Mildon HVLP Oil Pump
Harden oil pump drive
Speed Pro L2266F Pistons
Speed Pro Plasma Chrome Molly file to fit rings
APR main studs, block was lined bored
YL rods shoot penned, polished beams and harden and APR rod bolts
APR head bolts
346 heads
2.14 Manley intake and Fera 1.80 stainless steel valves
All new seats
All new steel guides
Matched ported
MP P3690933 springs and matching retainers
Heads cc at 88 cc’s
MP Roller chain
Crane custom cut push rods
MP HP stamped rocker arms and shafts
72 440 intake
Felpro 1215 intake gasket
Steel balancer


If the Desk top dyno is have way right will make 685 HP at a mer 5200 RPM's and 600 foot pounds. Say it is off 15% that is still 582 HP and 510 foot pounds. Part that made my head hurt at 2000 RPM's 300 HP and 789 Foot pounds.

I am tired of fighting at my age, stock 440 is starting to sound pretty good to me.  PM me and we will talk Have a line on a 25,000 Mile 440 69 motor like I care about the date codes.

                                        Cuda Ken

[BBMoparFreak]

Ken, not doubting what you're saying, but just wanting to get this figured out.
According to this: http://www.race-cars.net/calculators/et_calculator.html
It will take 545 RearWheel HorsePower to get a 11.02 ET for a  3700 LB (being generous) Charger.

And BlockHugger, don't  cut up that car!  Its worth more than that, and is only growing in value.  Especially an original BB car, and if it has any options at all, and is in good condition.

Michael

[cudaken]

 I just did it with a trap speed at 119 so that would be right at a 11.2. Showed 486 rear wheel HP. Hum, what can you say. I all so listed it at 3700 pounds. I will stick with my bible, has not let me down yet.

                                    Cuda Ken

[caddman]

you will have to let us know what you have to do to get down to 3700.
are you gutting it out or keeping it on the street?
don't forget to tie your frame rails, i neglected that with my 440 and stress cracked the paint on the driver side A pillar.  sounds like a great challenge though.

[cudaken]

 I broke the windsheild. I sort of thing Block Hugger is gone.

                                                     Cuda Ken

[caddman]

i have a question for you cuda ken, i'm looking all over for a rubber isolator that is bolted into the lower steering column of my 73 charger (just above the steering box). would you know of anyone that would have a spare?

thanks

caddman

[blockhugger]

Nah I am still here ...Had a heroin overdose in the family ... to busy to talk right now....

[Chryco Psycho]

i have a question for you cuda ken, i'm looking all over for a rubber isolator that is bolted into the lower steering column of my 73 charger (just above the steering box). would you know of anyone that would have a spare?

thanks

caddman

Check the Help parts in a local parts store I know they have them

Hang in there BH 

[cudaken]

 Sorry to hear that BH. Hope it was not someone you where close to.

                                        Cuda Ken