Tool Descriptions

[TX9 Charger]

Tool Definitions

DRILL PRESS:  A tall upright machine useful for suddenly snatching flat
metal bar stock out of your hands so that it smacks you in the chest
and flings your beer across the room, denting the freshly-painted part
which you had carefully set in the corner where nothing could get to it.

WIRE WHEEL: Cleans paint off bolts and then throws them somewhere
under the workbench with the speed of light. Also removes fingerprints
and hard-earned calluses from fingers in about the time it takes you
to say, ''What the...F#(K?''

ELECTRIC HAND DRILL: Normally used for spinning pop rivets in their
holes until you die of old age.

SKILL SAW: A portable cutting tool used to make studs too short.

PLIERS: Used to round off bolt heads. Sometimes used in the creation
of blood-blisters.

BELT SANDER: An electric sanding tool commonly used to convert
minor touch-up jobs into major refinishing jobs.

HACKSAW: One of a family of cutting tools built on the Ouija
board principle. It transforms human energy into a crooked,
unpredictable motion, and the more you attempt to influence its
course, the more dismal your future becomes.

VISE-GRIPS: Generally used after pliers to completely round off
bolt heads. If nothing else is available, they can also be used to
transfer intense welding heat to the palm of your hand.

WELDING GLOVES: Heavy duty leather gloves used to prolong the
conduction of intense welding heat to the palm of your hand.

OXYACETYLENE TORCH: Used almost entirely for lighting various
flammable objects in your shop on fire. Also handy for igniting the
grease inside the wheel hub you want the bearing race out of.

TABLE SAW: A large stationary power tool commonly used to launch
wood projectiles for testing wall integrity.

HYDRAULIC FLOOR JACK: Used for lowering an automobile to the
ground after you have installed your new brake shoes, trapping the
jack handle firmly under the bumper.

EIGHT-FOOT LONG YELLOW PINE 2X4: Used for levering an automobile
upward off of a trapped hydraulic jack handle.

E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than
any known drill bit that snaps neatly off in bolt holes thereby ending
any possible future use.

BAND SAW: A large stationary power saw primarily used by most
shops to cut good aluminum sheet into smaller pieces that more easily
fit into the trash can after you cut on the inside of the line instead
of the outside edge.

TWO-TON ENGINE HOIST: A tool for testing the maximum tensile
strength of everything you forgot to disconnect.

CRAFTSMAN 1/2 x 24-INCH SCREWDRIVER: A very large pry bar that
inexplicably has an accurately machined screwdriver tip on the end
opposite the handle.

AVIATION METAL SNIPS: See hacksaw.

PHILLIPS SCREWDRIVER: Normally used to stab the vacuum seals
under lids and for opening old-style paper-and-tin oil cans and
splashing oil on your shirt; but can also be used, as the name
implies, to strip out Phillips screw heads.

STRAIGHT SCREWDRIVER: A tool for opening paint cans. Sometimes
used to convert common slotted screws into non-removable screws.

PRY BAR: A tool used to crumple the metal surrounding that clip
or bracket you needed to remove in order to replace a 50 cent part.

HOSE CUTTER: A tool used to make hoses too short.

HAMMER: Originally employed as a weapon of war, the hammer
nowadays is used as a kind of divining rod to locate the most
expensive parts adjacent the object we are trying to hit.

MECHANIC'S KNIFE: Used to open and slice through the contents of
cardboard cartons delivered to your front door; works particularly
well on contents such as seats, vinyl records, liquids in plastic
bottles, collector magazines, refund checks, and rubber or plastic
parts. Especially useful for slicing work clothes, but only while
wearing them.

DAMMIT TOOL: Any handy tool that you grab and throw across the
garage while yelling ''DAMMIT'' at the top of your lungs. It is
also, most often, the next tool that you will need to use.

[tan top]

  thats some funny stuff   ..... damnit tool    Wire wheel    where the hell do the bolts go !!!

[Hemidog]

Funny! I always have a dammit tool handy!

[jackel440]

every tool is a dammit tool.They just don't know it yet!

[WingCharger]

The DAMMIT TOOL here, unfortunately, was the original 4-Point distributor, coil, and drive mechanism pack to my 1953 Farmall Super C...

[FLG]

Ive always found that nut to be right on the table. You loose it, search frantically....you then try to replicate its trajectory with a similar nut you see where it goes but still dont understand why your other nut is not next to it so you again try to replicate its trajectory with numerous nuts and find nothing. You then curse all the way to the store and buy a new one only to realize the one you lost is simply on the table you were working on.

Seriously though, anyone else use um "Similar nut trajectory theorey"??

It HAS worked on occasion   

[d72hemi]

Ive always found that nut to be right on the table. You loose it, search frantically....you then try to replicate its trajectory with a similar nut you see where it goes but still dont understand why your other nut is not next to it so you again try to replicate its trajectory with numerous nuts and find nothing. You then curse all the way to the store and buy a new one only to realize the one you lost is simply on the table you were working on.

Seriously though, anyone else use um "Similar nut trajectory theorey"??

It HAS worked on occasion   

guilty here! Occasionaly it does work

[tan top]

Ive always found that nut to be right on the table. You loose it, search frantically....you then try to replicate its trajectory with a similar nut you see where it goes but still dont understand why your other nut is not next to it so you again try to replicate its trajectory with numerous nuts and find nothing. You then curse all the way to the store and buy a new one only to realize the one you lost is simply on the table you were working on.

Seriously though, anyone else use um "Similar nut trajectory theorey"??

It HAS worked on occasion   

guilty here! Occasionaly it does work

    has worked for me also ..on times  ........