News:

It appears that the upgrade forces a login and many, many of you have forgotten your passwords and didn't set up any reminders. Contact me directly through helpmelogin@dodgecharger.com and I'll help sort it out.

Main Menu

What's your best 'low buck' upgrade on your Charger?

Started by CB, August 21, 2008, 08:49:11 AM

Previous topic - Next topic

craigandlynda

best, lowest buck improvement was swapping out original headlites for newer, brighter type...

Foreman72

Eric "Foreman"

Previous: 1972 Dodge Charger
Current: 2002 Volvo S60

"The steps of a man are ordered by the LORD, and He delights in his way. Though he fall, he shall not be utterly cast down; For the LORD upholds him with His hand.
=Psalm 37:23-24=
"But store up for yourselves treasures in heaven..."
=Matthew 6:19-21=
:pat

craigandlynda

get the halogen type that came out in the 1980's...they look the same as original sealed beams, but shine farther and whiter...available any good auto parts store

Ryan

XV motorsports seat belts  $120   I feel much safer with them

08 charger srt-8 power front buckets, only cost me $200 after I sold my 70 highbacks. Made the car a million times more enjoyable.
69 charger r/t Triple Black
   572 HEMI, Passion 5 speed, 4.10 Dana under construction

2014 viper TA

mikesbbody

ditching the points, going for electronic ignition (msd 6al) so much better  :2thumbs:

ITSA426

One of the lowest buck upgrades I've done is feed it a few gallons of 110 leaded racing gas.  It seems to like that.  I remember when that wasn't really an upgrade, but the gas we buy now is a step or two above cattle urine.

CB

so we got:

suspension:
rear springs / suspension bushings


electric:

headlight/relay upgrade
ignition conversion / electronic voltage regulator
converting ammeter to volt meter
battery disconnect
(130 amp denso) alternator

safety:

fire extinguisher / seat belts /  locking gas cap


Looks like the electric parts on our Mopars definitely could use some upgrades  :scratchchin:
1968 Dodge Coronet 500

moparjohn

OK really simple one esp. for those who don't have a 6 way.  Take the seat spacer out of the rear of your front seat mounting bolts and stack it on the front . More rake to the seat, more comfy.
Happiness is having a hole in your roof!

dkn1997

Quote from: moparjohn on August 23, 2008, 08:07:11 PM
OK really simple one esp. for those who don't have a 6 way.  Take the seat spacer out of the rear of your front seat mounting bolts and stack it on the front . More rake to the seat, more comfy.

i'm now doing this mod tomorrow....that's great!!
RECHRGED

Foreman72

do u have a 4 speed or a torqueflight? cuz if you have a auto i would suggest a B&M shift kit...makes for much snappyer shift...

Its a relatively simple upgrade right guys? i'll be putting one as soon as i get to the tranny portion of the restoration...
Eric "Foreman"

Previous: 1972 Dodge Charger
Current: 2002 Volvo S60

"The steps of a man are ordered by the LORD, and He delights in his way. Though he fall, he shall not be utterly cast down; For the LORD upholds him with His hand.
=Psalm 37:23-24=
"But store up for yourselves treasures in heaven..."
=Matthew 6:19-21=
:pat

Bad 69 Charger

Quote from: Death1970Proof on August 21, 2008, 04:13:15 PM
Quote from: CB on August 21, 2008, 08:49:11 AM
I think one of the best upgrades that won't cost you big $$$ would be going from points to electric ignition.
Also an aluminum radiator (with bigger flow) and a trans cooler would be affordable.
When thinking about safety of course adding disc brakes is necessary but that's already a +1K project.

What do you guys think is a big improvement over stock that wouldn't break the bank?

:coolgleamA: CB

Im all about budget but $1k for disc brakes???   :o WHOA! Let me let you guys in on a secret!  You know the '73-76 abodies?? Such as duster,dart sport and valiant?? Find one of those and rob the spindles as they will bolt directly to your control arms! Get the spindles and hardware along with the correct proportioning valve and other than that just the general replacement stuff such as a new set of rotors,master cylinder and brake pads and wheel bearings while your in there. This is what Im doing on my '70 charger.   You could probably get out for around $350 or $400 and thats buying lots of stuff new  :2thumbs :Cannot afford the wilwood stuff so this is where I turned to...

I see how easy this will work but can you use this for 14 inch wheels, i would like to change to disc on the front but keep the 14, is there a chrysler vehicle you can rob the stuff from that work for this, thanks Ben

Brock Samson

 I know you want to change to slots, but if and when you do make sure you go to 15s cause the 14s are too small, i found having a properly done trans and the increase in tire/wheel size really helped reduce wheel spin in a significant way. plenty of threads here about the optimum wheel tire size, my SS springs though giving a bumpy ride, reduce the squat upon launch and shift that up down motion to forward motion.
ride quality will suffer however.
so how about an update on your starting woes?..  :popcrn:

70 Charger RT

LOW BUCK upgrade I made was sequential tail lights.  It can easily be done for under $100.  It may not add safety to your ride but I think it looks way cooooool.
70 Charger R/T - 440/6
07 BMW 328iS
04 GMC SLE 2500 Diesel

Bad 69 Charger

Well as you can tell by the picture i built a Ga General Lee, they had 14's on them and i found this rare set of vectors, so if i have to stay with drums i will, they stop good but know that disc are better, Ben

tripleblkr/t

My sunroof, was practically free once I scraped out the car it came in.

ply72rr


Steve P.

I have to say the best bang for the buck is a set of disc brakes from a salvaged Volare' .

Complete running car= $200.00

Remove all parts needed for the disc set up = Your labor.

Remove all salable parts , engine, tranny, etc. = Your labor.

Scrap car and other junk laying around in and outside of your shop. = Cash for new rotors, calipers, pads, hoses, dual master cyl. and prop. valve.

Install new disc brake set up = your labor..


All said and done = you have a more dependable braking system and a few spare bucks in your pocket.

It's a win/win situation.  Now get to work...  :cheers:


:Twocents:

Steve P.
Holiday, Florida

Death1970Proof

Quote from: Foreman72 on August 23, 2008, 08:38:12 PM
do u have a 4 speed or a torqueflight? cuz if you have a auto i would suggest a B&M shift kit...makes for much snappyer shift...

Its a relatively simple upgrade right guys? i'll be putting one as soon as i get to the tranny portion of the restoration...


I use a torqueflite trick that works very well and that is so cost effective and low buck that it costs only what the fluid and filter will cost!

I ran this on my duster drag car and it was killer! Very quick consistant shifting....

1. Drain/Drop the tranny pan  :eyes:...remove filter  :eyes:

2. Remove the bolts that hold the valve body and as you are pulling out the valve body you will see a black spring in it's own round pocket. This is called the accumilator spring and it softens your upshifts. Toss this spring out and discard it if ya wanna or put it in your scrap pile.Put your valve body back in place and grab the bolts and tighten as needed.

3.While the pan is of course still off you will notice on the side that there is a black spring that is held in by a piece of steel and an allen head screw. This is your line pressure adjustment.  I cheated on this because actually it's kind of hard to get an allen wrench in there so what I did was take an el cheapo allen wrench and cut some length off of the end of it.  Take your allen wrench and adjust the spring almost all way out. You want to turn it in the direction to where the spring is compressing out,not in.   DO NOT and I repeat do not adjust the spring out to where the springs flies out...If you do that it becomes a major PITA... Adjust it to where you want it. I go on theedge and adjust it out pretty far. I like the shift quick and snappy....


4. After that screw your tranny filter back on/Replace pan: Then put in some  el cheapo 'type f" fluid. Everybit as good as that $5 a quart ripoff stuff and way less $$$. Ive run it for years and like it  :2thumbs:

5.Fill to level needed...STOMP IT .....HOLD ON TO yOUR A**!! GRIN and wave at the camaro next to you as you pass him chirping your tires... :icon_smile_big:



..This is cheaper than any shift kit I know of.....
"Remember when I said this car was death proof? Well that wasnt' a lie-this car is 100%death proof- only to get the benefit of it honey you really need to be sitting in my seat"...

challenger70

Quote from: Death1970Proof on August 28, 2008, 11:36:13 PM
Quote from: Foreman72 on August 23, 2008, 08:38:12 PM
do u have a 4 speed or a torqueflight? cuz if you have a auto i would suggest a B&M shift kit...makes for much snappyer shift...

Its a relatively simple upgrade right guys? i'll be putting one as soon as i get to the tranny portion of the restoration...


I use a torqueflite trick that works very well and that is so cost effective and low buck that it costs only what the fluid and filter will cost!

I ran this on my duster drag car and it was killer! Very quick consistant shifting....

1. Drain/Drop the tranny pan  :eyes:...remove filter  :eyes:

2. Remove the bolts that hold the valve body and as you are pulling out the valve body you will see a black spring in it's own round pocket. This is called the accumilator spring and it softens your upshifts. Toss this spring out and discard it if ya wanna or put it in your scrap pile.Put your valve body back in place and grab the bolts and tighten as needed.

3.While the pan is of course still off you will notice on the side that there is a black spring that is held in by a piece of steel and an allen head screw. This is your line pressure adjustment.  I cheated on this because actually it's kind of hard to get an allen wrench in there so what I did was take an el cheapo allen wrench and cut some length off of the end of it.  Take your allen wrench and adjust the spring almost all way out. You want to turn it in the direction to where the spring is compressing out,not in.   DO NOT and I repeat do not adjust the spring out to where the springs flies out...If you do that it becomes a major PITA... Adjust it to where you want it. I go on theedge and adjust it out pretty far. I like the shift quick and snappy....


4. After that screw your tranny filter back on/Replace pan: Then put in some  el cheapo 'type f" fluid. Everybit as good as that $5 a quart ripoff stuff and way less $$$. Ive run it for years and like it  :2thumbs:

5.Fill to level needed...STOMP IT .....HOLD ON TO yOUR A**!! GRIN and wave at the camaro next to you as you pass him chirping your tires... :icon_smile_big:



..This is cheaper than any shift kit I know of.....

:scratchchin: your sure this doesn't mess anything up? :popcrn:
'68 383 A833 QQ1 Charger
'70  440 727 FY1 Challenger

moparstuart

Quote from: Death1970Proof on August 28, 2008, 11:36:13 PM
Quote from: Foreman72 on August 23, 2008, 08:38:12 PM
do u have a 4 speed or a torqueflight? cuz if you have a auto i would suggest a B&M shift kit...makes for much snappyer shift...

Its a relatively simple upgrade right guys? i'll be putting one as soon as i get to the tranny portion of the restoration...


I use a torqueflite trick that works very well and that is so cost effective and low buck that it costs only what the fluid and filter will cost!

I ran this on my duster drag car and it was killer! Very quick consistant shifting....

1. Drain/Drop the tranny pan  :eyes:...remove filter  :eyes:

2. Remove the bolts that hold the valve body and as you are pulling out the valve body you will see a black spring in it's own round pocket. This is called the accumilator spring and it softens your upshifts. Toss this spring out and discard it if ya wanna or put it in your scrap pile.Put your valve body back in place and grab the bolts and tighten as needed.

3.While the pan is of course still off you will notice on the side that there is a black spring that is held in by a piece of steel and an allen head screw. This is your line pressure adjustment.  I cheated on this because actually it's kind of hard to get an allen wrench in there so what I did was take an el cheapo allen wrench and cut some length off of the end of it.  Take your allen wrench and adjust the spring almost all way out. You want to turn it in the direction to where the spring is compressing out,not in.   DO NOT and I repeat do not adjust the spring out to where the springs flies out...If you do that it becomes a major PITA... Adjust it to where you want it. I go on theedge and adjust it out pretty far. I like the shift quick and snappy....


4. After that screw your tranny filter back on/Replace pan: Then put in some  el cheapo 'type f" fluid. Everybit as good as that $5 a quart ripoff stuff and way less $$$. Ive run it for years and like it  :2thumbs:

5.Fill to level needed...STOMP IT .....HOLD ON TO yOUR A**!! GRIN and wave at the camaro next to you as you pass him chirping your tires... :icon_smile_big:



..This is cheaper than any shift kit I know of.....
You had me till you said type (f fluid ) which is way different then dextron/mecon not good to run that stuff in your mopar .  :Twocents: :Twocents:   Were you tweeking a c-6 maybe ?
GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

CB

Quote from: Steve P. on August 28, 2008, 11:10:38 PM
I have to say the best bang for the buck is a set of disc brakes from a salvaged Volare' .

Complete running car= $200.00

Remove all parts needed for the disc set up = Your labor.

Remove all salable parts , engine, tranny, etc. = Your labor.

Scrap car and other junk laying around in and outside of your shop. = Cash for new rotors, calipers, pads, hoses, dual master cyl. and prop. valve.

Install new disc brake set up = your labor..


All said and done = you have a more dependable braking system and a few spare bucks in your pocket.

It's a win/win situation.  Now get to work...  :cheers:


:Twocents:



Sounds like a good plan but too bad we don't have Volares in our junk yards  :icon_smile_angry:
CB
1968 Dodge Coronet 500

bullit68

another angle on the electonic conversion.i recently converted one of my cars by ordering a reman dist from the auto parts store for a 78 dodge truck 440($68),i changed out the heavy advance weight spring inside with another light one(out of any elec. dist.)to get quicker advance(like the mp unit).i got an orange control box from the wreckers($10-i bought a spare.btw a lot of mid 80's chryslers have them factory installed)then i bought the mp wiring conversion harness($24)and put it in.all told $102 spent.less than half the price of buying the kit with the same result.

Steve P.

Sorry CB. I sometimes forget that we are not ALL here in North America.

:cheers:
Steve P.
Holiday, Florida

drifter69

Plug in a AC/DC CD and you are automaticly upgraded. :Twocents:

Ghoste

Just tossing the spring away from your accumulator is a bad idea.  If want to take the accumulator out of the picture you need to install a blocker rod in there as well.