MoparStuart's Convertible Superbird Project Pic's

[WINGIN IT]

Dang, where was that picture taken ? Arkansas ?  

its a salvage yard princess  

Funny Stu
But you have to admit, you post a pic like that and it leads to all sorts of questions:

1. Is the dog named Princess?
2. Is that your backyard ( and therefore your dog , I guess) ?
3. Do you normally transport driveshafts on the hood of your black  c-dan?

[moparstuart]

Dang, where was that picture taken ? Arkansas ?  

its a salvage yard princess  

Funny Stu
But you have to admit, you post a pic like that and it leads to all sorts of questions:

1. Is the dog named Princess?
2. Is that your backyard ( and therefore your dog , I guess) ?
3. Do you normally transport driveshafts on the hood of your black  c-dan?

Inquirery minds wanna know

[mauve66]

     got a tranny jack to night hope to change out the throw out bearing saturday and or  sunday

you mean the one we told u to change BEFORE you put the tranny in???








any no, i haven't made it to the mailbox yet, its on the list though....................   right behind a good nap...........

[moparstuart]

     got a tranny jack to night hope to change out the throw out bearing saturday and or  sunday

you mean the one we told u to change BEFORE you put the tranny in???








any no, i haven't made it to the mailbox yet, its on the list though....................   right behind a good nap...........

[moparstuart]

got a used dash mounted reverse lamp

[moparstuart]

New console tranny boot  from Herb's parts  ( was dropped shipped direct ) from BE&A  so now you know who makes them

[moparstuart]

  new pedal treads and chrome dress up also from herbs

[moparstuart]

  re purposed the old console shifter boot to make it the new floor hole cover boot

  should work great had to cut off the two top rolls and then stretch out the side .  drill four hole and screw her down

[moparstuart]

all to keep dirt and weather from coming up this hole

[moparstuart]

  old rear seal boot was ripped so we got a new seal

[moparstuart]

   New seal from Oreillys  8 bucks

[moparstuart]

old out new in

[moparstuart]

  ive had the new throw out bearing for over a month , but been burnout plus waiting on the drive shaft
so finally my oldest son came over yesterday and we started tackleing it

   the new tranny jack works great with a manual tranny

[moparstuart]

 

[moparstuart]

 

[moparstuart]

  :drool5:new bearing had to pull the roll pin and change out the quick change viper fitting for a screw on fitting for the screw on line from the clutch master .  then bolted her in . she is in and ready

[moparstuart]

tranny came out quick , but was fighting us and didnt wanna slide back in so we quit about 8 pm last night and will start fresh today

[moparstuart]

 

[mauve66]

that's the same tranny jack i used, did you get it from harbor freight??

the shifter boot you got from Herbs, was it cheaper than BE&A (even though it ceme from them) or do you just like working with Herb??

p.s. going to mail box tomorrow

[moparstuart]

that's the same tranny jack i used, did you get it from harbor freight??

the shifter boot you got from Herbs, was it cheaper than BE&A (even though it ceme from them) or do you just like working with Herb??

p.s. going to mail box tomorrow

it was 69 bucks from herbs not sure what b e & a  want  
  i only paid 10 bucks shipping for it and the treads and chrome dress up so  i didnt get charged double shipping either

[ACUDANUT]

Where are the pic's of it running. You finished today right ?

[tan top]

    

[ACUDANUT]

Crickets ......

[JB400]

Drive shaft too short?

[pettybird]

Drive shaft too short?