News:

It appears that the upgrade forces a login and many, many of you have forgotten your passwords and didn't set up any reminders. Contact me directly through helpmelogin@dodgecharger.com and I'll help sort it out.

Main Menu

MoparStuart's Convertible Superbird Project Pic's

Started by MOPARHOUND!, August 17, 2007, 01:29:18 PM

Previous topic - Next topic

moparstuart

end of day three   

   and not much left of the expensive new crossmember


     
GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

Quote from: stroker400 wedge on December 29, 2012, 10:34:38 PM
So, he's helping with just installing the trans then, and afterwards you'll take it home and clean it up.  Makes sense.  How much more do you have to do?
drive shaft is a custom built  3 1/2 inch  aluminum one and once everythink is installed we have to send off measurements to have it built
 
GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

thedodgeboys

Quote from: stroker400 wedge on December 29, 2012, 10:18:57 PM
Looks good Stu :2thumbs:  Just wandering, why did you use a plasma cutter( or torch) to cut out the center hump instead of a cut off wheel?  It might not have been the fastest way to do it, but it would have been cleaner and saved some more work later on.

It's a total hack job  :coolgleamA:

Yah a body saw would have been nice, Stuart should have bought me one for Xmass  :smilielol:It would have looked better.  :nana:

A few minuets with a grinder and it will look ok  :icon_smile_big: this isn't chop cut rebuild its hack swear and pray it works  :nana: :slap: :smilielol: :smilielol: :rofl:

:cheers:

moparstuart

Quote from: thedodgeboys on December 30, 2012, 06:56:14 AM
Quote from: stroker400 wedge on December 29, 2012, 10:18:57 PM
Looks good Stu :2thumbs:  Just wandering, why did you use a plasma cutter( or torch) to cut out the center hump instead of a cut off wheel?  It might not have been the fastest way to do it, but it would have been cleaner and saved some more work later on.

It's a total hack job  :coolgleamA:

Yah a body saw would have been nice, Stuart should have bought me one for Xmass  :smilielol:It would have looked better.  :nana:

A few minuets with a grinder and it will look ok  :icon_smile_big: this isn't chop cut rebuild its hack swear and pray it works  :nana: :slap: :smilielol: :smilielol: :rofl:

:cheers:

:2thumbs: :2thumbs: :2thumbs: :2thumbs: :2thumbs:
GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

JB400

Quote from: thedodgeboys on December 30, 2012, 06:56:14 AM
Quote from: stroker400 wedge on December 29, 2012, 10:18:57 PM
Looks good Stu :2thumbs:  Just wandering, why did you use a plasma cutter( or torch) to cut out the center hump instead of a cut off wheel?  It might not have been the fastest way to do it, but it would have been cleaner and saved some more work later on.

It's a total hack job  :coolgleamA:

Yah a body saw would have been nice, Stuart should have bought me one for Xmass  :smilielol: It would have looked better.  :nana:

A few minuets with a grinder and it will look ok  :icon_smile_big: this isn't chop cut rebuild its hack swear and pray it works  :nana: :slap: :smilielol: :smilielol: :rofl:

:cheers:

Sounds about right then :lol: It lookin good :2thumbs:

moparstuart

Day 4 trim and do final tweeks on the hole , final test fit of tranny ( we hope )  built upper crossmemebr support to go over the tranny and start building the sheet tunnel back


  i started by taking the grinder and cleaning up the plasma cuts 
GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

 :2thumbs: :2thumbs:  final test fit
GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

i will most likely use one of these shifter arms

i would like to use the console style 70 shifter but if i do i will have to cut it right on the big off set bend and then
drill two holes to mount it to the new shift tower
GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

I will order carbon fiber black grips and a six speed indicator shift pattern
GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

 :drool5: :drool5: :drool5: the mount is to short , we will have to shim it to get the motor high enought to get the pan up off the drag link
GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

Hemidog

I bet you're looking forward to shifting through those gears!  :popcrn:

BigBlockSam

QuoteI will order carbon fiber black grips and a six speed indicator shift pattern


:2thumbs: :2thumbs: :cheers:
I won't be wronged, I wont be Insulted and I wont be laid a hand on. I don't do these things to others, and I require the same from them.

  [IMG]http://i45.tinypic.com/347b5v5.jpg[/img

moparstuart

GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE

moparstuart

GO SELL CRAZY SOMEWHERE ELSE WE ARE ALL STOCKED UP HERE