Anyone put on their own R/T stripe?****Updated with Pics****

[Mfr426]

Well, I'm continuing on my RT conversion on my 69 SE. My next move is to put the R/T stripe on the ass end. I have after market quarters on my car and I thought I remember someone saying that the marker lights might not be 100% in the right spot.

First, has anyone done this themselves and can they offer any advice?

Second, who has the best decals for this? I like David at Performance Car Graphics but am open to opinions.

Thanks for any comments.

PS: Donor 440 is now at the machine shop getting prepped for a stroker kit

[Silver R/T]

They have stripe kit on ebay. I did quick rattle can job on my 68 R/T

[Mfr426]

I've seen the kits. Just wondering who on the board has done their own install. The kit's not cheap so I want to make sure do my homework first...

Thanks for your comments.

Mike

[41husk]

I did it with help from cuda ken and another body guy.  it was harder than it looked and we kept having problems with little bubbles.  When I get ready for the stripes and hood black out on the Challenger, I will pay to have it done.

[Nacho-RT74]

I installed my rallye stripes. Is not easy if you don't have patiente. Keep wet the surface with water and a little soap solution to move it and align the stripes and will be fine. JUST A LITTLE BIT OF SOAP since it makes more bubbles than normally will have without.

[y3chargerrt]

My strip installed was 99.00 for the labor. Came out perfect so it was worth it.

[Just 6T9 CHGR]

I did mine myself after 2 failed attempts by "professionals"

I bought mine from PCG as well.  Follow thier instructions & you will be fine.  For the soap I used a small amt of Dreft baby cloths detergent & water as per Dave's instructions.
Start on one quarter and mark the position of each piece of the stripe before actually gluing it down as a guide.

I started on the left side quarter making sure to get the marker light housing in the center of the stripe and to have the top of the "T" in R/T in line with the center body line of the quarter....the rest "falls" into place.
Take your time & have a hair drier ready to help with the smoothing.   Small bubbles will come out with direct sunlight/heat...dont sweat the small ones.  the larger ones you will have to work out.  i dont recommend popping with a pin (personal prefrence)
I do believe the fact about the repro quarters being "off" in the marker light area.....my left quarter is a repro....by the time I got to the rightr side I had to do some minor tweeking to get it right...nothing major though.

[bill440rt]

Just6T9 has the right idea, of COURSE!!!
I did both my Chargers myself, my '70 I did twice (not by any mistakes). Both cars came out just fine. I've also done '70 Challenger black-out hoods, roof & hood strobe stripes on '71-'72 Road Runners, Superbird nose cones, Indy Ram Pickups, etc. If you've never applied stripes before of any kind, then you may want to seek help from a professional.
However, they really aren't that hard, as long as yout take your time. Here's how I do mine:

1) First, clean the car. The surface must be dust, wax, etc free.
2) Lay out your side stripes. Center them in the marker opening, & make sure the "curve" on the top matches the upper belt line. The stripes are cut this way to follow the body lines, just make sure you line these bends up. Hold them in place with small pieces of masking tape.
3) Lay out your trunk stripe. If the sides are on correctly, then the trunk stripe should line up evenly across the deck lid. Make sure the center "V" matches that of the deck lid. Hold this stripe in place temporarily with small pieces of tape.
4) Then, I like to lay out about 2" strips of masking tape parallel with the stripe, right up against it. I'll do this every foot or so. Once this is laid out, I'll mark it with pencil lines on the tape & onto the stripe. So, when I lay out the stripes for real, I simply have to place it along the tape edges, & line up my pencil marks.
5) Take the stripes off the car, & work one 1/4 panel at a time. Use a tack rag to remove any remaining traces of dust on the car. Peel off the backing, & spray the stripe with your soap mixture (I use Surf detergent mixed with water). Spray the same mixture on the car. Do NOT use a sponge or soap from a bucket to do this! Use a clean spray bottle to apply it.
6) Once soaped up, lay out your stripe on the car lining up your tape markings from before, & plaicing the stripe within the tape edges. Squeegee out any water, & wipe with a paper towel. Move on the the next stripe, & finally the deck lid.
7) Use a hair dryer while squeegeeing out any last traces of water. After about 20min or so, you should be able to peel off the top paper. Work out any remaining air bubbles as you go. Like Just 6T9 said, smaller ones are not a problem. Larger ones that can't be worked out can be popped with a very small, SHARP pin. Do not use anything too large or blunt or you will see a hole afterward close-up. Use a razor blade to trim around the marker opening & other areas.

Good Luck!

[bookedbydano]

You can definately do it. take your time and follow the great tips posted. I did mine and turned out great.  It is true you will not get all the small bubbles out.  They will come out with some drying time and sunlight.

[Mfr426]

Thank you all. These comments are perfect!

Can anyone give me a close up of the side marker light and how the decal covers it? Not sure I understand if it's under the light or over the light.

Thanks again. My R/T conversion is moving along nicely. I'll post some shots in the near future.

[bookedbydano]

remove the whole side marker bezel.  the strip goes under the bezel.  Have to paint the bezel whatever the stripe color is.

[Just 6T9 CHGR]

Remove the housing & stripe right over the opening....cut an "X" in the material over the opening & fold it back onto the inner quarter making sure to "mold" the vinyl into the creases for the housing....
From what I have read in resto books this is the correct look for inside the trunk....Not 100% sure though

[Mfr426]

Hey Thanks Chris, nice shot! I presume you painted your rear side markers to match the black stripe?

I hate to be a pain but could I ask you to take a picture of the R/T emblem on the rear tail panel? I just finished migging the SE holes closed, sanding and primering the area but am not sure where the new R/T emblem is located between the lock and the bottom. Any chance of measuring from the bottom of the lock assembly to the top of the R/T emblem for reference? I'm assuming it is centered between the tail light openings but the top to bottom location alludes me.

Thanks for the help. Next summer I'll buy you a beer at ACN...

[Just 6T9 CHGR]

Mike check this thread out.....

http://www.dodgecharger.com/forum/index.php/topic,10560.0.html

As far as measuring right now is a bit tough.  I have the car tucked away backed in the garage for the winter, butted up against the wall...Im sure someone else in a much warmer climate can help

[Mfr426]

No, this thread works fine. Thanks Chris.

Mike...

[sharpspike]

check out this site, it shows one being put on.  click- restoration - body & paint- detail & decals. hope its of some help.

http://www.69hemi.com/

[Mfr426]

Hey, great find and it's about time he updated his site! 

The downside is that his car is the exact same year and color combo (F8 with a black top) as mine is. I was sold on the white R/T stripe but now that I see his I wonder if the black is a better choice.

Oh well, that's a great reference. Thanks for posting.

MIke

[sharpspike]

hey mike, dont you have a link to your restoration? if you do can you repost it. seems i remember one, or im just getting old.

[69hemi]

check out this site, it shows one being put on.  click- restoration - body & paint- detail & decals. hope its of some help.

http://www.69hemi.com/

Try this URL it will take you right to the stripe deal.

http://www.69hemi.com/detaildecals/page_01.htm

[Mfr426]

I let my domain and site die on the vine. No time to update it and it got so stale that I had to pull the plug...

[69hemi]

I let my domain and site die on the vine. No time to update it and it got so stale that I had to pull the plug...

Mine was that way for a while but i have started updating it and I will have the Hemi Charger section finished in Jan then start on the new project section.  I got so many e-mails wondering what was going on I was amazed so I had go back to the keyboard and start finishing it up

[THE CHARGER PUNK]

Hey Thanks Chris, nice shot! I presume you painted your rear side markers to match the black stripe?

I just finished migging the SE holes closed

you closed up the holes on the roof that say SE? why would you do that?, you could have made an R/T SE clone instead of just an R/T

[Mfr426]

Let me clarify...I closed my tail panel Charger holes, NOT my SE emblem on my roof.

Must be all the paint fumes...

[sharpspike]

I let my domain and site die on the vine. No time to update it and it got so stale that I had to pull the plug...

Mine was that way for a while but i have started updating it and I will have the Hemi Charger section finished in Jan then start on the new project section.  I got so many e-mails wondering what was going on I was amazed so I had go back to the keyboard and start finishing it up

great site 69hemi. as well as a great car.

[69hemi]

<Many tanks!  I should be able to finish up the Hemi section in Jan so check back