Glovebox lock removal...I'm stumped!

[AKcharger]

if you can lock the glove box, key is correct. Actually any key is able to keep down that tab when is pressed and key inserted, but just the correct key will allow and spin the cylinder to lock then to reach that tab.

Well the key goes all the way in but turning it only opens the latch, no locking. So I guess that's the issue, you need the ORIGINAL key. well at least I have my answer now why it wasn't working.

[b5blue]

I didn't have the right key for my 70. (?)

[Nacho-RT74]

BINGO! is not release the latch but lock it! once is locked, which is what makes the barrel spins around 180°,  the tab appears there!!!

Then, remove key ( with system still locked ), press the tab, insert the key back and THAT'S the moment where the locking tab the same as the cylinder tabs will keep down to pull out the barrel out of the latch housing

[b5blue]

Yea what he said.

[Nacho-RT74]

If you want to get a full matched set, its available.

https://www.classicindustries.com/product/all-years/plymouth/barracuda/parts/md2655.html

[70 sublime]

Still comes down to why would you want to take it apart if you have the right key but you can not take it apart if you have the wrong key and need to change it ?

[Nacho-RT74]

he already said is not able to lock it, so it doesn't have the right key. I think he oly wants to paint the glove box lid.

This takes me to a question. Do you have the console lid with cylinder or without ? it should also match with it.

[AKcharger]

Nacho is right, just want to paint it, it's cleaner with lock removed.

- What a stupid set-up if you loose your key...you can NEVER change the lock!
- nope bench seat, no console
- no super bigge just mask and paint, still annoying though
- good to know match sets are out there but you'd need a machinist to remove the lock without damaging the door

[b5blue]

So you put a key in and have the latch up like as if the door was closed when inside the car? Key in-latch up-look for release through hole. 

[70gtx440dana]

It is very easy to pop off the chrome knob. Just stick a flat screw drive in the end where the key goes....only slightly.... and pry it to one side. It will pop of easily. Then for re-assembly use your bench vise and a socket or similar item to press it back on. Super easy way to remove it if you do not have the key. Note: when you re-assemble there are alignment features you have to align properly. Good luck!

[AKcharger]

So you put a key in and have the latch up like as if the door was closed when inside the car? Key in-latch up-look for release through hole. 

...and use the key to turn the lock so the pin is exposed in the little hole. Unfortunately if  you don't have the right key not gonna happen

[AKcharger]

Take that stupid lock!

[b5blue]

Like NEW!!

[AKcharger]

I was tempted to give it "the finger" in the photo but thought that crude 

[b5blue]

I been there many times also! 

[Nacho-RT74]

- good to know match sets are out there but you'd need a machinist to remove the lock without damaging the door

no... I just got vicegrips catching by the outside knob and pulled out hard... it came out... I didn't know how to make the job and went rude. After that just learnt how it works LOL... but I could reassembly it back.

[DoubleDlover]

There are actually TWO windows with that little brass tang you push down. The one you can see with the lock bolded in place. And the one you CANT see on the side. Take out the bolts and spin the lock a little and bingo the hidden window appears. Thats the one you use to take it out with OUT the key. 

[Nacho-RT74]

But you'll need to press every tab because the deal with the key is not just the locking tab but all the barrel tabs kept pressed to allow to pull it out clean.

[john108]

I may have missed something as I haven't read all 42 posts but my 68 Charger trunk key works the glove box and console.

[green69rt]

I may have missed something as I haven't read all 42 posts but my 68 Charger trunk key works the glove box and console.

I missed it also, this is a 3rd gen.  May not be the same as our 68 or 69.

[Nacho-RT74]

yes, is the same than previous years. But if trunk cylinder was changed sometime in the past and "accidentally" the factory trunk key was lost you don't have the glove box key either anymore.

I have at this moment on my car 2 trunk keys... one just for the trunk which I replaced, the other one still the original which works to both glovebox on my car