flat black chargers wheel and tire options

[Sixtyeight]

Hi,

Here is mine, with Vectors and steelies...





Jeroen.

What size are those steel wheels. And what size tires
I see most are running the wheel opening trim. I've debated going that route.

Luke

The steel wheels are 8' x 15 rear and  original 6' x 14 front...

Tires: 255/60R15 and 205/70R14

Jeroen.

[jwells1993]

thanks guys picked up some new to me rims today i think they look good wasnt sure bout the gray center but its growin on me

[alfaitalia]

Look good to me....Size? Offset?

[jwells1993]

Look good to me....Size? Offset?

15x7 torque thrust guessin offset is 3.75 not sure ill have to messure

[Troy]

Look good to me....Size? Offset?

15x7 torque thrust guessin offset is 3.75 not sure ill have to messure

You'll be limited in the tire size you can put on those (based on the width and backspacing) but they'll be nice.

Troy

[jwells1993]

Look good to me....Size? Offset?

15x7 torque thrust guessin offset is 3.75 not sure ill have to messure

You'll be limited in the tire size you can put on those (based on the width and backspacing) but they'll be nice.




i still havent measured haha what am i measuring for? just from where rim meets hub to lip of rim?

Troy

[alfaitalia]

Place a straight edge across from side to side on the back rim of the wheel....measure from the straight edge to the hub mating surface (where the bolt holes are)....that is your backspacing.

[Troy]

Look good to me....Size? Offset?

15x7 torque thrust guessin offset is 3.75 not sure ill have to messure

You'll be limited in the tire size you can put on those (based on the width and backspacing) but they'll be nice.




Troy

i still havent measured haha what am i measuring for? just from where rim meets hub to lip of rim?

I don't know if you have to measure... those only come in one offset!

But I misspoke, 3.75" on a 7" width isn't too bad as it's almost centered just like the factory wheel. It's -6mm (1/4") but you can't fit a wide enough tire on there to hit anything - especially in the back.

Troy

[jwells1993]

Look good to me....Size? Offset?

15x7 torque thrust guessin offset is 3.75 not sure ill have to messure

You'll be limited in the tire size you can put on those (based on the width and backspacing) but they'll be nice.




Troy

i still havent measured haha what am i measuring for? just from where rim meets hub to lip of rim?

I don't know if you have to measure... those only come in one offset!

But I misspoke, 3.75" on a 7" width isn't too bad as it's almost centered just like the factory wheel. It's -6mm (1/4") but you can't fit a wide enough tire on there to hit anything - especially in the back.

Troy

so your saying i should be good to go?

[Troy]

Look good to me....Size? Offset?

15x7 torque thrust guessin offset is 3.75 not sure ill have to messure

You'll be limited in the tire size you can put on those (based on the width and backspacing) but they'll be nice.




Troy

i still havent measured haha what am i measuring for? just from where rim meets hub to lip of rim?

I don't know if you have to measure... those only come in one offset!

But I misspoke, 3.75" on a 7" width isn't too bad as it's almost centered just like the factory wheel. It's -6mm (1/4") but you can't fit a wide enough tire on there to hit anything - especially in the back.

Troy

so your saying i should be good to go?

Yes, but the maximum width tire you can put on them is a 225.

Troy

[jwells1993]

ok thanks troy

[alfaitalia]

These are clearly the way forward.....you wont look like all the other generic mat black Chargers with these mo-fo,s rolling on all four corners!!!



......unless of course they is juz too Gansta for yooz bruv!!