1967 Dodge Charger rear outer wheel housing

[Yellow Charger]

I need both the left and right rear outer wheel housing for my 1967 Dodge Charger.  Companies are remaking them for 1968 and up but not 1966 or 67.  Does any one know of where I can find any good rust-free used ones?  Thanks!  rkcrump@mtco.com

[Ghoste]

Are you talking about the 1/4 panel sheet metal?

[Yellow Charger]

No, it is the outer rear wheel housing:  The metal that goes around the rear wheel opening.  Inner wheel housings are available, but I can not find the outer wheel housing for 66 or 67 Dodge Chargers which are the same.  The 1968 outer wheel housings are available, but are different.  I am willing to purchase the entire lower quarter panel and outer wheel housing as one unit if necessary.  I need both sides. Thanks!  rkcrump@mtco.com

[wingcar]

Is it this part over the wheel well....or some other part......

[Ghoste]

I think good used ones might be the only option unless you luck into some NOS ones.  

[ODZKing]

2529538 & 2529539 (R-L).
I've have read over the years that guys have "massaged" 68 ones into the quarter and made them work but I have never seen it done so I can't speak from experience.
I know they don't list inner fenders for 66-7 either and the 68's will work with very little fussing involved, AGAIN, I'm told.
So either you look at a 68 and see if they compare and try or used.  But used ones are going to be rough no mater how hard you look for one.

[Musicman]

No one makes them...

[A383Wing]

No one makes them...

and nobody probably never will, either

[Ghoste]

If they haven't done exterior sheet metal, you are probably 100% on that.

[70-500-SE-EXPORT]

Your best bet is used from a vintage car wrecking yard. Pick up a hemmings. heres a few places to try:
http://www.wildcatmopars.com/
http://www.allamericanclassics.com/
http://www.stevesparts.com/
http://www.stephensperformance.com/
http://www.dvap.com/
http://www.tonysparts.com/

[GPULLER]

No one makes them...

and nobody probably never will, either

What a bunch of Debbie Downers...I'm keeping all hope alive!

[wingcar]

No one makes them...

and nobody probably never will, either

What a bunch of Debbie Downers...I'm keeping all hope alive!

AMD is busy developing panels for the Edel and Studebaker, when those finally come out they will start work on First Generation Charger pieces......    

[GPULLER]

No one makes them...

and nobody probably never will, either

What a bunch of Debbie Downers...I'm keeping all hope alive!

AMD is busy developing panels for the Edel and Studebaker, when those finally come out they will start work on First Generation Charger pieces......    

That and the AMC Marlin. 

[Yellow Charger]

Wingcar:  Yes, you have the correct picture of the outer wheel housing.

[VegasCharger]

Try this guy, he might have what you need, you never know

http://lasvegas.craigslist.org/pts/4963105846.html

[GPULLER]

Holy motherload!

[Bronzedodge]

Not sure where you are but spring Carlisle is this weekend....

     http://www.carlisleevents.com/carlisle-events/carlisle-spring-swap-meet-corral-auction/default.aspx

[Yellow Charger]

I can not attend the Carlisle show, but if anybody sees some rear outer wheel housings for a 67 Dodge Charger, give me a call (309-369-1213) and perhaps we can work out a deal.

The person in Vegas sold the rear quarters and outer wheel housings about 30 minutes before I called him this a.m.

Thanks!

[Musicman]

It wasn't me 

Desert Valley Auto probably has them, but be prepared for the $ticker $hock...

[VegasCharger]

I can not attend the Carlisle show, but if anybody sees some rear outer wheel housings for a 67 Dodge Charger, give me a call (309-369-1213) and perhaps we can work out a deal.

The person in Vegas sold the rear quarters and outer wheel housings about 30 minutes before I called him this a.m.

Thanks!

That's bad timing, I mean 30 minutes is way too close. Actually this guy was in Utah (St. George) but he had it listed in local Las Vegas CL. That's how I came acrossed it.

Sorry for your luck.

[Yellow Charger]

I have called about a dozen places and no one has these 67 rear outer wheel housings.  How much metal work would I need to do on a 68 rear outer wheel housing?  I can purchase new ones for a 68.  Thanks!

[Yellow Charger]

HELP!  I am still looking for the rear outer wheel housing for my 67 Dodge Charger.  I need both sides.  I have called about 10 places - nothing available.  Would it be a lot of work to fabricate a 68 into a 67 housing?

[A383Wing]

find a parts car

[VegasCharger]

Try these 

https://columbus.craigslist.org/pts/4963717246.html

http://richmond.craigslist.org/pts/5007132953.html

http://pittsburgh.craigslist.org/cto/4927159135.html

https://chicago.craigslist.org/nch/pts/5007293744.html

http://atlanta.craigslist.org/eat/pts/5000873097.html