Need help identifying parts

[440 magnum]

I have these parts that i dont know where they are assigned to go.  The clips, I thought were for the headliner but I think im wrong. The other piece i dont know either.  anyone know where they belong??

[71_Charger_R/T]

The first picture of the bracket, is a cruise control bracket. It mounts on the driver's side inner fender just rearward of the fender tag.

[440 magnum]

Thanks! I would have never guessed it would be that

[Charger-Bodie]

The clips are for wiring behind the dash ,like the clove box light wires. Looks like a lot of them though.

[ODZKing]

Yes, usually there is only 2 or 3.  They clip to the edge of the underside of the dash and basically keep wires from falling down.
The headliner clips are much larger than that.

[440 magnum]

thanks guys! 
So I have another question.  Did the 69 charger offer cruise control?  I dont think it did.  My dad was the original owner of this car and if i remember correctly he used to say that he liked hitting 100 miles an hour and kicking in the cruise control while on HWY 5.   

[Charger-Bodie]

Yes. You could get cruise on a 69 Charger.

[twodko]

I think the plate item is part of the front inner fender splash shield assembly.

[Ghoste]

You sure?

[twodko]

Good morning Ghoste,

Yes I'm certain that's what that plate is. If you look in the front wheel well toward
the front of the car it's the piece that bolts to the bottom of the inner fender sheet metal. At 
the bottom of this plate there is a flap of that flexible splash shield stuff mounted to it.
The FSM might show this.

I cheated a bit when I resto'd my car. When I removed these plates they
had a lot of factory undercoating on them. I scraped that stuff off and sprayed the plates
with "chassis black" paint. Don't tell anyone..........I could be banned from the forum. 

[Ghoste]

Oh ok, so they would normally be covered with undercoating then?

[twodko]

That I can't say for sure but mine were.

[440 magnum]

I just came back from looking inside the front wheelwell and cant figure out where this piece is attached.  Is it righ behind the valance? Anyone share any pictures?

[Charger-Bodie]

That is defiantly a cruise servo bracket.

[440 magnum]

Charger-Bodie.  do you have any pictures you can share.  I went to check, and I none of the existing holes line up with the bracket struds. 

[Charger-Bodie]

https://www.google.com/search?client=safari&hl=en&biw=1024&bih=672&tbm=isch&sa=1&ei=vnvpU-G1JpOAygSnkIH4Aw&q=69+charger+cruise+control+pics&oq=69+charger+cruise+control+pics&gs_l=tablet-gws.3...27991.33814.0.34060.15.15.0.0.0.1.261.1787.4j8j2.14.0....0...1c.1.51.tablet-gws..12.3.467.kdNoXjAu5hg#facrc=_&imgrc=bBAT2Q-DCGR5LM%253A%3BCvbwDYCsqbnS7M%3Bhttp%253A%252F%252Fwww.dodgecharger.com%252Fforum%252Findex.php%253Faction%253Ddlattach%253Btopic%253D80226.0%253Battach%253D149664%253Bimage%3Bhttp%253A%252F%252Fwww.dodgecharger.com%252Fforum%252Findex.php%253Ftopic%253D80226.0%3B640%3B480

[twodko]

If I can get on my knees to shoot a pix tomorrow.......just had spinal surgery 4 wks ago, you'll see
where it mounts.

[Ghoste]

It sure does look like the bracket in this photo.  I don't want you in pain or worse twodko but I sure would like to know for curiousity sake.

[tan top]

It sure does look like the bracket in this photo.  I don't want you in pain or worse twodko but I sure would like to know for curiousity sake.

   hope your ok !! anything to do with the back is major problems  

took  this picture , to save you the trouble  


( yeah I know it should be undercoated , but at the time I was putting it back together decided to leave them in primer  )
& bumper brackets should be black , !! but found no trace of black on mine when taking it apart , not even inside the two halfs each side ,  car never had a wreck either ( all panels were original to the car )  

[Ghoste]

So it is for sure the cruise bracket then.

[tan top]

 yes    looks like it could be 

I did have a lot of good pictures saved of a complete cruise set up , dismantaled ! but !! those picture files were amongst those I lost last year  

this is all I have now

[twodko]

Hey thanks TT, you da man. 70 virgins, pizza and beer incoming your location.

[John_Kunkel]

I've got a lot of cruise control servo brackets and none have tilted studs like the one in the OP...IOW, the studs are straight across from each other. 

A tape measure laid next to the bracket would help.

[Ghoste]

 

[71_Charger_R/T]

  These are all cruise servo brackets........... '71- '73- '70 Notice the one on the right (missing a stud) canted bolt pattern and looks just like the one in the OPs first post.
I don't know how much more evidence some people need.  IT IS A CRUISE SERVO BRACKET!!   :pulling hair:

[440 magnum]

Thanks for the effort.  Holes on the Servo Bracket line up with the holes on the inner fender.