Will it fit?? 295/50 R15 on 15x8" with -12 offset

[cougs]

gang,
I can't find this answered anywhere.  Will a 295/50 R15 Mickey Thompson Sportsman fit a 68 charger when mounted on a 15x8" rim with a 4.00 BS (-12 offset)?  I'm worried about hitting my fender. 

Thanks!

Brock

[68X426]

It doesn't appear so, based on this calculator. http://vexer.com/68rt/old_outdated_badly_coded_old_old_old_wheelguide.html

Experiment with it to see what answer you get.

[cdr]

if you trim the outer lip a little it should fit.i have 15x10  5in back spacing with 295-50 & have room

[HPP]

I have 15x10 with 5" backspace, so I think the 4" you are looking at could be an issue, but, you also are putting a 295 on an 8" rim, so you are going to suck the sidewalls in a bit. You might also have to run that set up at 25-28 psi to get a full footprint from the tire. Personally, I'd try to go at least  4.5 backspace to eliminate any potential for clipping the lip.

[Patronus]

I guarantee that tire will hit your fender.

[68CoronetRT]

What about a 275/65/15 with this same rim?

[1974dodgecharger]

if you trim the outer lip a little it should fit.i have 15x10  5in back spacing with 295-50 & have room

CDR what your tire size?  I plan to run 295/40/20 on mine rims with zero offset and 5.5 backspace....hopefully she fit.

[cdr]

295-50-15

[cougs]

What about a 275/65/15 with this same rim?

Too tall for the look I'm going for.  I'm going to play it safe and find a 4.5 backspace 8" rim.  The only problem is that I can't find a straight-spoke torque thrust with a 4.5 backspace.  All I can find is Torque Thrust D or the Torque Thurst II which have a rounded "D" and curved spoke.  The NVT70R American is an awesome wheel but why the hell don't they make it in a zero offset??   

Or I can go with a 255/60 R15 Tire which has some decent width with this wheel.   

http://www.summitracing.com/parts/are-t70r5865

[68CoronetRT]

What about a 275/65/15 with this same rim?

Too tall for the look I'm going for.  I'm going to play it safe and find a 4.5 backspace 8" rim.  The only problem is that I can't find a straight-spoke torque thrust with a 4.5 backspace.  All I can find is Torque Thrust D or the Torque Thurst II which have a rounded "D" and curved spoke.  The NVT70R American is an awesome wheel but why the hell don't they make it in a zero offset??   

Or I can go with a 255/60 R15 Tire which has some decent width with this wheel.   

http://www.summitracing.com/parts/are-t70r5865

Yea, but will that tire size work with that rim? I understand that's not the look your going for.

[cougs]

Oh, it would fit just fine

[HPP]

Check these guys for wheels;

http://www.team3wheels.com/production_wheels.html

http://www.rocketracingwheels.com/rocket-racing-wheels/c28

[cougs]

I have, and the Rocket strike may be the wheel I go with.  IMO, E-T wants too much for their five spoke wheel.  Another alternative is Vintage Wheel Inc.   

[c00nhunterjoe]

I have 15x8.5 with a 4" bs and run 275/60/15 (28"tall) they clear about a finger to the outer lip. I don't see 295 fitting

[Dino]

275 fits with 4 bs, 295 does not BUT not all 295's are created equal either so you need to find out exactly how wide the tire is.  I don't think it would take all that much work to fit a 295 with that bs but 4.5 will be a direct fit.  Question is:  how close would you like the tire to sit to the fender lip?  Imo the closer the better.

[cougs]

I ended up ordering 15x10s with a 5.5 backspace to play it safe.  Now my sidewalls will look the same.  Costing quite a bit more but I think I'll be happier.

[Dino]

I ended up ordering 15x10s with a 5.5 backspace to play it safe.  Now my sidewalls will look the same.  Costing quite a bit more but I think I'll be happier.

That'll be a direct fit with room to spare on either end, I think you'll be very happy.

[myk]

It doesn't appear so, based on this calculator. http://vexer.com/68rt/old_outdated_badly_coded_old_old_old_wheelguide.html

Experiment with it to see what answer you get.

UGH, my new wheel/tire 'combo is too far inboard...

[Dino]

According to that software, my tires hit the quarter lip and have a lot of space towards the inside.  It's the opposite in real life though, it hits the inside and has room to spare on the outside.

It all depends on the brand of wheel and tire.

[myk]

Actually, your rear tire is just about perfect, IMO...

[Dino]

Actually, your rear tire is just about perfect, IMO...

I'm very happy with it but it does rub ever so slightly on the inside.  Check my 'Before I start' thread for the pics.  If I can move them out about 1/2" then they'll be prefect.  Maybe swapping the rear drums for discs can give me the option to bring them out a bit.

Still, it's nitpicking, I do love how these wheels look on my old beater.

[cougs]

Hate to recommend it but some 3/8" spacers would probably fix it

[myk]

Hate to recommend it but some 3/8" spacers would probably fix it

Are spacers a bad thing?  Would spacers require longer wheel studs? Dino, would you ever consider spacers?

[Dino]

Hate to recommend it but some 3/8" spacers would probably fix it

Hate to recommend it but some 3/8" spacers would probably fix it

Are spacers a bad thing?  Would spacers require longer wheel studs? Dino, would you ever consider spacers?

I'm not sure I want to go that route but then again, the only spacers I've seen are those cheap things at the local auto stores.  I'm sure there's better stuff out there yet few people think it would be a good idea.

I would definitely need longer wheel studs, there's no way you can decrease them by 1/2" and still have enough thread left.

[cougs]

The spacers at the auto parts store are not a bad thing as long as they are not too thick.  But yes, longer studs are required but they're easy to replace.